[MAME]

    Blitz '99 board:

    Seattle 5770-15206-08
        1x R5000 CPU (heatsink covering part numbers)
        1x Midway 5410-14589-00 IO chip
        1x Midway 5410-14590-00 ??
        1x Midway 5410-15349-00 Orbit 61142A ??
        1x ADSP-2115
        1x Midway security PIC Blitz 99 25" 481xxxxxx (U96)
        1x mid sized QFP (Galileo?) has heatsink (u86)
        1x mid sized QFP (PixelFX?) heakstink (u17)
        1x mid sized QFP, smaller (TexelFX?) heatsink (u87)
        12x v53c16258hk40 256Kx16 RAM (near Voodoo section)
        1x PC87415VCG IDE controller
        1x lh52256cn-70ll RAM  (near Galileo)
        1x 7can2 4k (unknown Texas Instruments SOIC)
        2x IDT 7201 LA 35J  (512x9 Async FIFO)
        1x DS232AS serial port chip
        1x Altera PLCC Seattle A-21859 (u50)
        1x Altera PLCC PAD_C1 (u60)
        3x IS61C256AH-15 (32Kx8 SRAM) near ADSP
        1x TMS418160ADZ (1Meg x 16 RAM) near ADSP
        4x TMS418160ADZ (1Meg x 16 RAM) near CPU
        1x TVP3409-17OCFN (3dfx DAC?)
        1xAD1866 audio DAC
        1x Maxim max693acwe (watchdog) near 2325 battery and Midway IO chip
        4MHz crystal attached to security PIC
        14.31818MHz crystal near 3dfx DAC
        16MHz crystal attached to ADSP
        16.6667MHz crystal near Midway IO chip
        33.3333MHz crystal near IDE chip and Galileo(PCI bus I assume)
        50MHz crystal near CPU

    Boot ROM-1.3
    Sound ROM-1.02

    Connectors:
        P2 and P6 look like PCI slots, but with no connectors soldered in, near
            3dfx/Galileo/IDE section.
        P19 is for the Daisy Dukes widget board(used by Cal Speed), and maybe
            the Carnevil gun board.
        P28 is a large 120 pin connector that is not populated, right next to
            the CPU.
        P20 is a 10 pin connector labeled "factory test".
        P1 is a 5 pin unpopulated connector marked "snd in" no idea what it
            would be for.
        P11 is a 5 pin connector marked "snd out" for line level stereo output.
        P25 is a standard IDE connector marked "Disk Drive" P15 is a laptop
            sized IDE connection right next to it.
        P9 and P10 are 14 pin connectors marked "Player 3 I/O" and player 4
            respectively.
        P16 is a 6 pin marked "Aux in"
        P3 is a 6 pin marked "Bill in"
        P8 is a 14 pin marked "Aux Latched Outputs"
        P22 is a 9 pin marked "serial port"

-

[Aug/11/2002]

Here is the NFL Blitz 99 ROM dump. Only two EPROMS were on the board, the boot rom
and the sound rom. I'm guessing a sound rom is needed as firmware to control
the DCS system (I think blitz99 uses the DCS sound system like MK4).
The boot rom is needed because it runs off of a hard drive.
No serial number or specs of the hard drive were on the hard drive so
i'm not sure how big it is. A hard drive dump will come later when i get
the extra pc to back up with. Dolly.exe will be used.
Dumped on 8/11/02 at around 2AM. I'm not sure what revision the boot rom
is because the sticker was peeled off.
Sound rom's revision is 1.02

-